Would you like to make this site your homepage? It's fast and easy...
Yes, Please make this my home page!
================================================================================
Note 5.0 Q22 Compatible Options No replies
JAWS::KAISER 319 lines 25-MAR-1985 09:15
--------------------------------------------------------------------------------
+---------------+ +-----------------+
| d i g i t a l | | uNOTE # 005 |
+---------------+ +-----------------+
+----------------------------------------------------+-----------------+
| Title: Q22 Compatible Options | Date: 23-Apr-84 |
+----------------------------------------------------+-----------------+
| Originator: Charlie Giorgetti | Page 1 of 6 |
+----------------------------------------------------+-----------------+
This is a list of Q22 compatible options. A Q22 compatible option is
defined as a Q-bus option that will work without restriction in an
extended Q-bus system, that is a 22-bit Q-bus system. This list also
includes options that are not compatible in Q22 systems and the reason
for the restriction.
The requirements for a device to be Q22 compatible are the following:
1. Processors, memories, and DMA devices must all be capable of 22-bit
addressing.
2. Devices must use backplane pins BC1, BD1, BE1, BF1 and DC1, DD1,
DE1, DF1, for BDAL18-21 only.
Processors, memories, or DMA devices which are not capable of 22-bit
addressing may generate or decode erroneous addresses if they are used
in systems which implement 22-bit addressing. Memory and
memory-addressing devices which implement only 16 or 18-bit addressing
may be used in a 22-bit backplane, but the size of the system memory
must be restricted to the address range of those devices (64 KB for
systems with 16-bit devices and 256 KB for systems with an 18-bit
devices).
Any device which uses backplane pins BC1, BD1, BE1, BF1 or DC1, DD1,
DE1, DF1, for purposes other than BDAL18-21 is electrically incompatible
with the 22-bit bus and may not be used without modification.
NOTE
Eighteen or sixteen bit DMA devices can potenitially work in
Q22 systems by buffering I/O in the 18- or 16-bit address
space.
I. Fully Compatible Options
Options in this category meet both of the requirements mentioned above
and may be used in any Q-bus configuration.
A. Processors
KD32-A M7135/M7136 MicroVAX I CPU Module
KDF11-A M8186 LSI-11/23 CPU
(Etch Rev. C or later)
Page 2
KDF11-B M8189 LSI-11/23B CPU
KDJ11-A M8192 LSI-11/73 CPU
KDJ11-B M8190 MicroPDP-11/73 CPU
KXT11-C M8377 Q-bus Perpherial I/O Processor
KMV11-A M7500 Q-bus Perpherial Communication Processor
B. Backplanes/Boxes
H9270-Q 4 X 4 Q22/Q22 Backplane
H9281-QA 2 X 4 Q22 Dual-height Backplane
H9281-QB 2 X 8 Q22 Dual-height Backplane
H9281-QC 2 X 12 Q22 Dual-height Backplane
H9275 4 X 9 Q22/Q22 Backplane
BA11-S H9276 4 X 9 Q22/CD Backplane
Micro/PDP-11 H9278 4 X 3 Q22/CD and 4 X 5 Q22/Q22 Backplane
C. Memory
MCV11-D M8631 CMOS Non-volatile Memory
MSV11-L M8059 MOS Memory (either 128 KB or 256 KB)
MSV11-P M8067 MOS Memory (either 256 KB or 512 KB)
MSV11-Q M7551 MOS Memory (1 MB)
MXV11-B M7195 Multifunction Module
MRV11-D M8578 PROM/ROM Module
D. Options
AAV11-C A6006 D/A Converter
ADV11-C A8000 A/D Converter
AXV11-C A0026 D/A and A/D Combination Converter
BDV11 M8012 Bootstrap, Terminator, Diagnostic
(CS Rev. E or later, ECO M8012-ML005
installed)
DEQNA M7504 Ethernet Controller
DLV11 M7940 Asynchronous Serial Line Interface
Page 3
DLV11-E M8017 Asynchronous Serial Line Interface
DLV11-F M8028 Asynchronous Serial Line Interface
DLV11-J M8043 Four Asynchronous Serial Line Interfaces
(CS Rev. E or later, ECO M8043-MR002
installed)
DHV11 M3104 8-line Asynchronous EIA Multiplexer
DMV11-AD M8053-MA Synchronous Communications Interface
DMV11-AF M8064-MA Synchronous Communications Interface
DPV11 M8020 Programmable Synchronous EIA Line
DRV11 M7941 32 line Parallel Interface
DRV11-J M8049 64 line Parallel Interface
DRV11-W M7651 General Purpose DMA Interface (dual)
DUV11 M7951 Programmable Synchronous EIA Line
DZQ11 M3106 4-line Asynchronous EIA Multiplexer (dual)
DZV11 M7957 4-line Asynchronous EIA Multiplexer (quad)
FPF11 M8188 Floating Point Processor
IBV11-A M7954 IEEE Instrument Bus Interface
IEQ11 M8634 DMA IEEE Instrument Bus Interface
KLESI-QA M7740 LESI Bus Adaptor (RC25 Interface)
KPV11-A M8016 Power-fail and LTC Generator
(KPV11-B and -C are not compatible)
KWV11-C A4002 Programmable Real-time Clock
LAV11 M7949 LA180 Line Printer Interface
LPV11 M8027 LA180/LP05 Printer Interface
RLV12 M8061 RL01/2 Controller
RQDX1 M8639 Controller for 5.25" Floppy and Winchester
RXV11 M7946 RX01 Floppy Disk Interface
TQK25 M7605 Streaming Cartridge Tape Controller
TSV05 M7196 Magnetic Tape Controller
Page 4
E. Bus Cable-Cards
M9404 Cable Connector
M9404-YA Cable Connector with 240-Ohm Terminators
M9405 Cable Connector
M9405-YA Cable Connector with 120-Ohm Terminators
II. Restricted Compatibility Options
Options in this category do not meet one or both of the requirements for
use in a 22-bit system. These options are incompatible with some or all
22-bit systems.
A. Processors
KDF11-A M8186 LSI-11/23 CPU
(Prior to etch rev. C, 18-bit addressing only,
and use of BC1,BD1,BE1,BF1 for purposes other
than BDAL18-21)
KD11-HA M7270 LSI-11/2 CPU
(16-bit addressing only, and use of BC1,BD1,
BE1,BF1 for purposes other than BDAL18-21)
KD11-F M7264 LSI-11 CPU
(16-bit addressing only, and use of DC1,DB1,
DE1,DF1 for purposes other than BDAL18-21)
KXT11-A M8063 SBC-11/21 CPU
(16-bit addressing only)
B. Backplanes/Boxes
DDV11-B 6 X 9 Backplane
(18-bit addressing only)
BA11-M H9270 4 X 4 Backplane
(18-bit addressing only)
BA11-N H9273-A 4 X 9 Backplane
(18-bit addressing only)
BA11-VA H9281-A,B,C 2 X n Dual-height Backplane n = 4, 8, and 12
BA11-VA used the H9281-A
(18-bit addressing only)
VT103 4 X 4 Backplane (part number: 54-14008)
(18-bit addressing only)
Page 5
C. Memories
MMV11-A G653 8 KB Core Memory
(16-bit addressing only, Q-bus required on C/D
backplane connectors)
MRV11-AA M7942 ROM Module
(16-bit addressing only)
MRV11-BA M8021 UV PROM-RAM
(16-bit addressing only)
MRV11-C M8048 PROM/ROM Module
(18-bit addressing only)
MSV11-B M7944 8 KB bus refreshed RAM
(16-bit addressing only)
MSV11-C M7955 32 KB RAM
(18-bit addressing only)
MSV11-D,E M8044/M8045 8 KB, 16 KB, 32 KB, 64 KB RAM
(18-bit addressing only)
MXV11-A M8047 Multifunction Module
(18-bit addressing only on memory, the memory
can be disbales see uNte #106)
D. Options
AAV11 A6001 D/A Converter
(Use of BC1 for purposes other than BDAL18)
ADV11 A012 A/D Converter
(Use of BC1 for purposes other than BDAL18)
BDV11 M8012 Bootstrap/Terminator
(CS Revision E or earlier 18 bits only)
DLV11-J M8043 Serial Line Interface
(CS Rev. E or earlier incompatible with
KDF11-A and KDF11-B)
DRV11-B M7950 General Purpose DMA Interface (quad)
(18-bit DMA only)
KPV11-B,C M8016-YB,YC Power-fail/line-time clock/terminator
(Termination for 18-bits only)
KUV11 M8018 Writable Control Store
(For use with KD11-F processor only)
KWV11-A M7952 Programmable real-time clock
(Use of BC1 for purposes other than BDAL18)
Page 6
REV11 M9400 Terminator, DMA refresh, bootstrap
(Bootstrap for use with KD11-F and KD11-HA
processors only.
Termination for 18-bits only.
DMA refresh may be used in any system.)
RKV11-D M7269 RK05 Controller Interface
(16-bit DMA only)
RLV11 M8013 RL01,2 Controller
M8014 (18-bit DMA only, use of BC1 and BD1 for
purposes other than BDAL18 and BDAL19)
RXV21 M8029 RX02 Floppy Disk Interface
(18-bit DMA only)
TEV11 M9400-YB 120-Ohm Bus Terminator
(Termination for 18-bits only)
VSV11 M7064 Graphics Display
(18-bit DMA only)
E. Bus Cable-Cards
M9400-YD Cable Connector
(18-bit bus only)
M9400-YE Cable Connector with 240-Ohm Terminators
(18-bit bus only)
M9401 Cable Connector
(18-bit bus only)
