|
|
================================================================================
Note 31.0 MSV11-QA Revision Differences No replies
FURILO::GIORGETTI 528 lines 21-AUG-1985 23:16
--------------------------------------------------------------------------------
+---------------+ +-----------------+
| d i g i t a l | | uNOTE # 031 |
+---------------+ +-----------------+
+----------------------------------------------------+-----------------+
| Title: MSV11-QA Revision Differences | Date: 28-JUN-85 |
+----------------------------------------------------+-----------------+
| Originator: Jack Toto | Page 1 of 9 |
+----------------------------------------------------+-----------------+
Digital Equipment Corporation recently announce the addition of three
memories for the Q-bus space; the MSV11-QA quad module at 1MB, the
MSV11-QB quad module at 2MB, and the MSV11-QC quad module at 4MB.
Earlier versions of the MSV11-QA were shipped using a revision A etch
and the documentation correctly showed the jumper configurations.
However early in 1985 the MSV11-QA/QB/QC started shipping with revision
C etch. The documentation at that point did not show how to properly
configure the C etch. It is the intent of this MicroNote to point out
the differences between the two modules and to explain the configuration
of both the etch revisions.
The two modules can be identified in any one of the three ways listed
in the table below;
1. The location and value of the modules serial number.
2. The location of CSR and address jumpers and switches.
3. The module's designation number, stamped on the insertion
handles will be different.
3A. Revision A modules will be labeled M7551-AA.
3B. Revision C modules will be labeled M7551-AA.
SERIAL NUMBER LOCATION
----------------------
The two modules can be identified by the location of its serial number.
The revision A module will have its serial number located in the upper
right hand corner of the module as you hold it with the fingers pointing
down or at you and the component side facing you or up as it would lay
on a work bench. This serial number will be 5017547A1. The location of
the serial number for revision C module will be on the component side
also, but in the upper left hand corner. This serial number will
be 5017547-01-C1. The attached diagrams of the revision A and revision
C modules show the location of these numbers.
237
uNOTE # 031
Pag 2 of 9
JUMPER LOCATION
---------------
The MSV11-QA revision A module allows for the selection of Block Mode
DMA transfers, parity detection, and extended address parity error
detection as well as CSR and address selection. The address selection
includes two switches, one for the modules starting address and one
for the modules ending address. The ending address switch is used to
control the decode logic on the module as the same etch is used for 2MB
and 4MB boards as well, each with different value memory chips to reach
there designed capacity. The location and function of these switches
and jumpers if detailed in the diagrams and configuration tables
attached to the end of this MicroNote.
The MSV11-QA revision C module does not allow for the selection of Block
Mode DMA or for the selection of parity detection, these features
are built into the module itself and can be used or not used through
hardware/software compatibility. When used in a system that supports
Block Mode the MSV11-QA will perform as a Block Mode device, when used
in a non Block Mode system it will perform as a normal memory module
without any decrease in that system's performance. When used with
software such as RSX11 and using mixed parity/non-parity memories
parity detection can be disabled through sysgen. The only functions
that a user is required to configure to use the MSV11-QA revision C is
CSR selection and starting and ending address. It should be pointed out
that the two switches for starting and ending addresses have been flip
flopped from the positions in which they were located on the revision A
module. Once again refer to the diagrams and configuration tables
attached to this MicroNote for location and function of these switches
and jumpers.
The following pages contain diagrams and tables for configuring the two
versions of the MSV11-QA
238
uNOTE # 031
Page 3 of 9
MSV11-QA revision A Module Identification
-----------------------------------------
+-----+ +-+ +-+ +-----+
| +____________|_|___________|_|____________+ |
+-----------------------------------------------------+
| |
| 5017547A1 <---------+- PRINTED CIRCUIT
| | BOARD NO.
| |
| |
| |
| |
| (COMPONENT SIDE) |
| |
| |
| |
| |
| |
| |
| |
| |
| +-+ +-+ +-+ |
++ +---+ | +-+ | +---+ | ++
| | | | | | | |
+--------+ +--------+ +--------+ +--------+
(A) MSV11-QA (ETCH revision A ONLY)
MSV11-QA revision A CSR SELECTION
---------------------------------
NUMBER OF JUMPER POSITION CSR REGISTER
MEMORY MODULE R P N M ADDRESS
---------------------------------------------------------------
1ST IN IN IN IN 17772100
2ND OUT IN IN IN 17772102
3RD IN OUT IN IN 17772104
4TH OUT OUT IN IN 17772106
5TH IN IN OUT IN 17772110
6TH OUT IN OUT IN 17772112
7TH IN OUT OUT IN 17772114
8TH OUT OUT OUT IN 17772116
9TH IN IN IN OUT 17772120
10TH OUT IN IN OUT 17772122
11TH IN OUT IN OUT 17772124
12TH OUT OUT IN OUT 17772126
13TH IN IN OUT OUT 17772130
14TH OUT IN OUT OUT 17772132
15TH IN OUT OUT OUT 17772134
16TH OUT OUT OUT OUT 17772136
239
uNOTE # 031
Page 4 of 9
MSV11-QA revision A STARTING AND ENDING ADDRESS
-----------------------------------------------
DESIRED SW1 SW2 STARTING ENDING
STARTING SWITCH SWITCH ENDING SWITCH
ADDRESS POSITION POSITION ADDRESS POSITION
-----------------------------------------------------------------------
IN KBYTE 12345 6 IN KBYTE 12345
-----------------------------------------------------------------------
0 00000 0 128 11111
128 11111 1 256 01111
256 01111 1 384 10111
384 10111 1 512 00111
512 00111 1 640 11011
640 11011 1 768 01011
768 01011 1 896 10011
896 10011 1 1024 (1MB) 00011
1024 (1MB) 00011 1 1152 11101
1152 11101 1 1280 01101
1280 01101 1 1408 10101
1408 10101 1 1536 00101
1536 00101 1 1664 11001
1664 11001 1 1792 01001
1792 01001 1 1920 10001
1920 10001 1 2048 (2MB) 00001
2048 (2MB) 00001 1 2176 11110
2176 11110 1 2304 01110
2304 01110 1 2432 10110
2432 10110 1 2560 00110
2560 00110 1 2688 11010
2688 11010 1 2816 01010
2816 01010 1 2944 10010
2944 10010 1 3072 (3MB) 00010
3072 (3MB) 00010 1 3200 11100
3200 11100 1 3328 01100
3328 01100 1 3456 10100
3456 10100 1 3584 00100
3584 00100 1 3712 11000
3712 11000 1 3840 01000
3840 00010 1 3968 10000
3968 10000 1 4096 (4MB) 00000
1 = off position (open)
0 = on position (closed)
NOTE: Switch S6 of SW1 is not used. For a memory starting address of
0, switch S6 of SW2 should be set to 0 (on). For all other
starting addresses S6 of SW2 should be off (1).
240
uNOTE # 031
Page 5 of 9
MSV11-QA revision A
-------------------
+-----+ +-+ +-+ +-----+
| +____________|_|___________|_|____________+ |
+-----------------------------------------------------+
| 5017547A1 |
| ++ +++ |
| PARITY -----> ++ A+++ <-----------+- CSR REGISTER
| LED ++ P+++ | SELECTION
| N+++ |
| M+++ |
| ++ |
| ++A <-------------+- ENABLE/DISABLE
| ++B | CSR SELECTION
| ++ |
| SW1 |
| ++++ |
| ++++1 <------------+- STARTING ADDRESS
| |++|2 | SWITCHES
| |++|3 ++ | (S6 NOT USED)
| |++|4 ++W1 <-----+- ENABLE/DISABLE
| (COMPONENT SIDE) |++|5 ++W2 | BLOCK MODE
| ++++6 ++ ++ |
| OFF ON ++K <--+- ENABLE/DISABLE
| ++L | EXTENDED
| SW2 ++ | ERROR ADDRESS
| ++++ |
| ++++1 <-----+- ENDING ADDRESS
| ++++2 | SWITCHES
| |++|3 |
| |++|4 |
| |++|5 |
| |++|6 |
| OFF ON |
| ++++ <-+- ENABLE PARITY
| +5V ++++ | ERROR DETECTION
| ++ JH |
| ++ <------+- NOT USED, MODULE
| ++ | DOES NOT SUPPORT
| +5VB | BATTERY BACKUP
| +-+ +-+ +-+ |
++ +---+ | +-+ | +---+ | ++
| D | | C | | B | | A |
+--------+ +--------+ +--------+ +--------+
Jumper and Switch Locations
(Drawing not to scale)
241
uNOTE # 031
Page 6 of 9
MSV11-QA revision C Module Identification
-----------------------------------------
+-----+ +-+ +-+ +-----+
| +____________|_|___________|_|____________+ |
+-----------------------------------------------------+
| |
PRINTED CIRCUIT -+---------> 5017547-01-C1 |
BOARD NO. | |
| |
| |
| |
| |
| (COMPONENT SIDE) |
| |
| |
| |
| |
| |
| |
| |
| |
| +-+ +-+ +-+ |
++ +---+ | +-+ | +---+ | ++
| | | | | | | |
+--------+ +--------+ +--------+ +--------+
(B) MSV11-QA (ETCH revision C OR LATER)
MSV11-QB AND MSV11-QC
(Drawings not to scale)
MSV11-QA revision C CSR SELECTION
---------------------------------
NUMBER OF JUMPER POSITION CSR REGISTER
MEMORY MODULE J5 J7 J9 J11 ADDRESS
------------------------------------------------------------------------
1ST IN IN IN IN 17772100
2ND OUT IN IN IN 17772102
3RD IN OUT IN IN 17772104
4TH OUT OUT IN IN 17772106
5TH IN IN OUT IN 17772110
6TH OUT IN OUT IN 17772112
7TH IN OUT OUT IN 17772114
8TH OUT OUT OUT IN 17772116
9TH IN IN IN OUT 17772120
10TH OUT IN IN OUT 17772122
11TH IN OUT IN OUT 17772124
12TH OUT OUT IN OUT 17772126
13TH IN IN OUT OUT 17772130
14TH OUT IN OUT OUT 17772132
15TH IN OUT OUT OUT 17772134
16TH OUT OUT OUT OUT 17772136
242
uNOTE # 031
Page 7 of 9
MSV11-QA revision C STARTING AND ENDING ADDRESS
------------------------------------------
DESIRED SW2 SW1 STARTING ENDING
STARTING SWITCH SWITCH ENDING SWITCH
ADDRESS POSITION POSITION ADDRESS POSITION
-----------------------------------------------------------------------
IN KBYTE 12345 6 IN KBYTE 12345
-----------------------------------------------------------------------
0 00000 0 128 11111
128 11111 1 256 01111
256 01111 1 384 10111
384 10111 1 512 00111
512 00111 1 640 11011
640 11011 1 768 01011
768 01011 1 896 10011
896 10011 1 1024 (1MB) 00011
1024 (1MB) 00011 1 1152 11101
1152 11101 1 1280 01101
1280 01101 1 1408 10101
1408 10101 1 1536 00101
1536 00101 1 1664 11001
1664 11001 1 1792 01001
1792 01001 1 1920 10001
1920 10001 1 2048 (2MB) 00001
2048 (2MB) 00001 1 2176 11110
2176 11110 1 2304 01110
2304 01110 1 2432 10110
2432 10110 1 2560 00110
2560 00110 1 2688 11010
2688 11010 1 2816 01010
2816 01010 1 2944 10010
2944 10010 1 3072 (3MB) 00010
3072 (3MB) 00010 1 3200 11100
3200 11100 1 3328 01100
3328 01100 1 3456 10100
3456 10100 1 3584 00100
3584 00100 1 3712 11000
3712 11000 1 3840 01000
3840 00010 1 3968 10000
3968 10000 1 4096 (4MB) 00000
1 = off position (open)
0 = on position (closed)
NOTE: Switch S6 of SW2 is not used. For a memory starting address
of 0, switch S6 of SW1 should be set to 0 (on). For all other
starting addresses S6 of SW1 should be off (1).
243
uNOTE # 031
Page 8 of 9
MSV11-QA revision C
-------------------
+-----+ +-+ +-+ +-----+
| +____________|_|___________|_|____________+ |
+-----------------------------------------------------+
| |
| 5017547-01-C1 +++++ <--------------+-- CSR REGISTER
| +++++ | SELECTION
| +++++ |
| |
| |
| |
| |
| SW2 |
| ++++ |
| ++++1 <---+- STARTING ADDRESS
| ++++2 | SWITCHES
| ++++3 | (S6 NOT USED)
| ++++4 |
| ++++5 |
| ++++6 |
| (COMPONENT SIDE) |
| |
| |
| SW1 |
| ++++ |
| ++++1 <--------+- ENDING ADDRESS
| ++++2 | SWITCHES
| ++++3 |
| ++++4 |
| ++++5 |
| ++++6 |
| |
| |
| o o <-----+- BATTERY BACKUP
| o o | JUMPERS
| W2 o o W1 |
| o o |
| |
| +-+ +-+ +-+ |
++ +---+ | +-+ | +---+ | ++
| | | | | | | |
+--------+ +--------+ +--------+ +--------+
Jumpers and Switches
(Drawing not to scale)
244
uNOTE # 031
Page 9 of 9
COMPARISON OF SIMILAR FUNCTION JUMPERS
--------------------------------------
JUMPER SELECTABILITY ENABLED DISABLED
FUNCTION REV-A REV-A CONFIGURATION CONFIGURATION
----------------------------------------------------------------------
DISABLE YES NO W1 IN (J11 TO J12) W2 IN (J11 TO J10)
BLOCK MODE W2 OUT W1 OUT
-----------------------------------------------------------------------
DISABLE YES NO JUMPER B IN JUMPER A IN
PARITY (J14 TO 13) (J14 TO J5)
MEMORY JUMPER A OUT JUMPER B OUT
-----------------------------------------------------------------------
DISABLE YES NO JUMPER H IN JUMPER G IN
PARITY (J2 TO J3) (J1 TO J2)
DETECTION JUMPER G OUT JUMPER H OUT
-----------------------------------------------------------------------
DISABLE YES NO JUMPER L IN JUMPER K IN
22-BIT (J8 TO J7) (J8 TO J9)
ADDRESSING JUMPER K OUT JUMPER L OUT
-----------------------------------------------------------------------
BATTERY NO YES W3 AND W1 IN W4 AND W1 IN
BACKUP WITH WITH
SUPPORT W4 AND W1 OUT W3 AND W1 OUT
(revision C ONLY) (revision C ONLY)
----------------------------------------------------------------------
BATTERY BACKUP
CONFIGURATION NOTE: JUMPERS W4 AND W2 ARE LOCATED BETWEEN E21 AND
E13 IN THE LOWER RIGHT HAND CORNER OF THE
COMPONENT SIDE OF THE MODULE. FOR THE ACTUAL
LOCATION OF THESE AND ALL OTHER JUMPERS PLEASE
REFER TO THE USERS GUIDE.
245